Home \ Help \ Search \ Login RSS

Welcome, Guest. Please Login

This forum is now READ-ONLY! Please visit http://forum.wiring.co/ for the new forum.

Wiring Forum › Other questions › Other electronics/hardware questions › phototransistors

(Moderators: Titus, bhagman, barragan)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1
phototransistors (Read 11158 times)
03/28/10 at 14:37:27

John Keszler   Offline
YaBB Newbies

Posts: 11
 *
 
Dear Forum members,

I have bought two types of phototransistors
here are the links for their data sheet:
http://www.datasheetcatalog.org/datasheet/siemens/BP103-2.pdf
and
http://www.datasheetcatalog.org/datasheet/siemens/BPY62-4.pdf
but I don't know how to connect them Tongue
witch pin goes to ground, vcc, digital in or analog in.
that's another thing, I don't know whether they give me
an analog or digital signal ...
PS: i look in examples but the phototransistor there look
much different form the ones I got.

Thanks

Regards
John
 
Back to top 
IP Logged
 
Reply #1 - 03/28/10 at 18:04:33

barragan   Offline
YaBB Administrator

Posts: 939
 *****
 
hi John, you can connect them like this: http://books.google.com/books?id=6JRcqhVUszEC&pg=PA365&lpg=PA365&dq=connecting+phototransistor+to+microcontroller&source=bl&ots=q1zeulP56k&sig=gHaCVl4f5KpEPrdQIxNoO0uWEps&hl=en&ei=hpmvS8n5H8T7lwf876HPAw&sa=X&oi=book_result&ct=result&resnum=10&ved=0CCcQ6AEwCQ#v=onepage&q=&f=false

the ECB pins are marked in the diagram on your datasheet for each device. I'll add a diagram for the next site update. Let me know of this helps.
 
Back to top 
IP Logged
 
Reply #2 - 03/29/10 at 16:14:16

Titus   Offline
YaBB Moderator
Wiring Soccer Robot!
Amsterdam

Posts: 176
 *****
 
The 22K Ohm resistor adjusts the sensitivity. You might want to exchange it for a Potentiometer.

Or connect it to an analogIn, rather then a digitalIn.
In that case the 22K Ohm resistor also regulates the sensitivity, but you can still adjust your calibration in the program(given the fact you will get value's from 0-1023).

Good luck,
 
Check www.TeamVossius.nl for our Autonomous soccer robots!
Back to top 
IP Logged
 
Reply #3 - 03/30/10 at 09:11:19

John Keszler   Offline
YaBB Newbies

Posts: 11
 *
 
Thanks Barragan,
I'm waiting for the site update, Cheesy
but now i have to connect a 6v Dc solenoid
I understand a solenoid is an electronic coil with a magnet in it ...
basically.
I was reading the forum ,and i found this :
http://wiring.org.co/cgi-bin/yabb/YaBB.pl?num=1147904339
and from there i tried going here:
http://wiring.org.co/reference/electronics/coil.html
but my browser kept saying 404 not found
should I connect in to an h-bridge or straight to wiring Undecided?
what is the circuit ?
and also when you want to power
the wiring ,were can you get batteries, that are
connectible to the"external power supply connector'.
and I read in the hardware section that you can also
power wiring by a regulated 5 volts and you connect it to and you connect it to any vcc pin?

thanks,

John
 
Back to top 
IP Logged
 
Reply #4 - 04/01/10 at 16:36:37

barragan   Offline
YaBB Administrator

Posts: 939
 *****
 
that's an old link, here you can find useful information about coils: http://www.kpsec.freeuk.com/components/relay.htm
also for transistors http://www.kpsec.freeuk.com/trancirc.htm
this one too, has a lot of diagrams for interfacing relays, coils and solenoids, I'll add this diagram to my list, perhaps we could do the example with your specific device Smiley
 
Back to top 
IP Logged
 
Reply #5 - 04/04/10 at 20:14:19

John Keszler   Offline
YaBB Newbies

Posts: 11
 *
 
Dear Barragan


I can't find anything on the web, on my solenoid and besides
the one I'm using is a practice solenoid (it's not even mine)
When I get one for myself i will send you specs, but until then
can you send me a link on how to connect a 10 A 6Vdc
solenoid with a relay .
That's anther thing , if my solenoid is 10A and 6 V dc then
do I have to use a relay that is exactly 10A and 6 V dc
or any thing in the vicinity would work
Thanks

Regards

John Alex
 
Back to top 
IP Logged
 
Reply #6 - 04/16/10 at 19:06:48

John Keszler   Offline
YaBB Newbies

Posts: 11
 *
 
HI all

Ok ... i ask to many questions Cheesy
I found this in the web:
http://interactive.usc.edu/members/phoberman/relayCircuit.gif
I'm asking can i use the same thing to control a solenoid:
I would replace the bulb with the solenoid .
and in the image the power pin is connected to a 5v
would i connect the power depending on the voltage of the coil?  and the other pin the is the ground, digital pin
do i need to use a transistor for it ?
my idea for a circuit is the attached file please
tell me if it's right.
This is the relay I'm using :
http://www.rapidonline.com/netalogue/specs/60-4660e.pdf
Thanks
Regards

John Alex Keszler
 
solenoid_cicuit.jpg (43 KB | 465 )
solenoid_cicuit.jpg
Back to top 
IP Logged
 
Reply #7 - 04/16/10 at 20:51:51

barragan   Offline
YaBB Administrator

Posts: 939
 *****
 
hi john, the circuit looks fine, note that the relay you're using already is a solenoid, it is also possible to use a MOSFET to control a solenoid, check out this circuit: http://wiring.org.co/learning/basics/mosfetirld024.html
replace the bulb for the solenoid and it should work, as you mentioned before "if my solenoid is 10A and 6 V dc" you don't need the relay just use the solenoid instead of the relay in the diagram you sent: http://interactive.usc.edu/members/phoberman/relayCircuit.gif
« Last Edit: 04/17/10 at 23:16:54 by barragan »  
Back to top 
IP Logged
 
Page Index Toggle Pages: 1
‹ Previous Topic | Next Topic ›